Home
Editorial Committee
Brief Instruction
Back Issues
Instruction to Authors
Submission on line
Contact Us
Chinese

  The journal resolutely  resists all academic misconduct, once found, the paper will be withdrawn immediately.

Title:Deformation characteristics and springback analysis of arc edge U-shaped parts
Authors: Lv Lin  Deng Ming  Wan Shu Liu Yaqi 
Unit: Chongqing University of Technology 
KeyWords: bending  springback  arc edge U-shaped part 
ClassificationCode:
year,vol(issue):pagenumber:2015,40(7):34-37
Abstract:

For the forming of arc ridge U-shaped cross section parts commonly used for car frame structure, the concept of plate arc edge U-shaped bending was defined and its geometry and forming characteristics were analyzed. The stress and strain distribution characteristics in the wings, the sides and the top during the forming were analyzed by numerical simulation. The springback of arc edge U-shaped bending was preliminarily studied. It is stated that the flange width and profile curvature are the main influence factors of the springback. Meanwhile, it is also discussed that the springback forms of arc edge U-shaped bending in the direction of the cross section and ridges with their interaction. Therefore, it is pointed out that the influence factors on bending springback including materials performance(modulus), size of the bending angle,relative bending radius and size of blank holder force in forming.

Funds:
重庆市应用开发类资助项目(cstc2014yykfA60002、cstc2013yykfc60004)
AuthorIntro:
吕琳(1968-),女,硕士,教授
Reference:



[1]钟志华. 薄板件冲压成形过程的计算机仿真[M]. 北京:北京理工大学出版社,1997.


Zhong Z H.Computer Simulation of Stamping Process of Sheet Parts[M].Beijing: Beijing Institute of Technology Press,1997.


[2]朱东坡,孙琨,李涤尘,等. 板料成形回弹问题研究新进展[J]. 塑性工程学报,2000, 7(1): 11-15.


Zhu D P,Sun K,Li D C,et al. New progress in the study of the problem of spring-back in sheet metal forming[J].Journal of Plasticity Engineering,2000,7(1):11-15.


[3]刘志云,何成宏,杨国泰,等.外缘内曲翻边时的应力应变分析[J].锻压装备与制造技术, 2003, 38(4): 28-31.


Liu Z Y,He C H,Yang G T,et al. Stress strain analysis of edge inward flanging[J].Equipment & Manufacturing Technology,2003,38(4):28-31.


[4]刘志云, 何成宏, 杨国泰, 等. 外缘外曲翻边时的应力应变分析[J]. 塑性工程学报, 2004, 11(1): 32-35.


Liu Z Y,He C H,Yang G T,et al. Stress strain analysis of convex curvature flanging[J].Journal of Plasticity Engineering,2004,11(1):32-35.


[5]聂昕.汽车板件回弹相关问题的研究[D].长沙:湖南大学,2008.


Nie X. Research on Automobile Plate Spring-back Related Problems[D].Changsha:Hunan University,2008.


[6]邓明,温彤.冲压工艺及模具设计[M].北京:化学工业出版社,2009.


Deng M,Wen T. Stamping Process and Die Design[M].Beijing: Chemical Industry Press,2009.

Service:
This site has not yet opened Download Service】【Add Favorite
Copyright Forging & Stamping Technology.All rights reserved
 Sponsored by: Beijing Research Institute of Mechanical and Electrical Technology; Society for Technology of Plasticity, CMES
Tel: +86-010-62920652 +86-010-82415085     Fax:+86-010-62920652
Address: No.18 Xueqing Road, Beijing 100083, P. R. China
 E-mail: fst@263.net    dyjsgg@163.com