Home
Editorial Committee
Brief Instruction
Back Issues
Instruction to Authors
Submission on line
Contact Us
Chinese

  The journal resolutely  resists all academic misconduct, once found, the paper will be withdrawn immediately.

Title:Experimental study on unloading rules in hydraulic system with large flow and high pressure
Authors: JIANG Ting-ting1 TAN Jian-ping1 SI Yu-xiao1 2 SUN Kang1 2 
Unit: 1. College of Mechanical and Electronic Engineering Central South University Changsha 410012 China 2. State Key Lab of Fluid Power Transmission and Control Zhejiang University Hangzhou 310027 China 
KeyWords: large-scale hydraulic press  unloading rules  hydraulic shock 
ClassificationCode:TG315
year,vol(issue):pagenumber:2012,37(5):80-83
Abstract:

To realize the stable and rapid unloading of large-scale hydraulic press and accurate proportional control of the process, the proportional cartridge throttle was utilized as the unloading valve with a displacement sensor in core. Experimental system with large flow and high pressure based on accumulator which supplied oil source was designed and established. The effect of different unloading curves and unloading time on hydraulic shock was investigated. The experimental results show that this experimental system can simulate the unloading process of system with large flow and high pressure, and the unloading curve based on the principle of energy uniform release makes the unloading time less than other unloading curves.

Funds:
国家科技重大专项(2009ZX04005-031);流体动力与机电系统国家重点实验室开放基金(GZKF-201023)
AuthorIntro:
Reference:


[1]杨军怀,陈国清.快速锻造液压机液压系统压力冲击的试验研究[J].中国机械工程,1994,5(3):14-17.
[2]Bergant A, Simpson A R, Tijsseling A S. Water hammer with column separation: A historical review[J]. Journal of Fluids and Structures,2006,22(2):135-171.
[3]杜森,马英江,高立斌,等. 解决大型液压机卸压冲击的新方法[J].锻压机械,1997,(4):33-35.
[4]杨宝光.锻压机械液压传动[M].北京:机械工业出版社,1981.
[5]俞新陆.液压机的设计与应用[M].北京:机械工业出版社,2007.
[6]陈柏金,黄树槐,魏运华,等. 锻造液压机高压卸载系统改进研究[J].液压与启动,2008,(1):57-59.
[7]陈柏金,黄树槐.锻造液压机液压系统传动方式研究[J].锻压技术,2003,28(2):44-47.
[8]司玉校,谭建平,孙康.基于能量均匀释放原则的工作缸卸荷曲线研究[J].锻压技术,2012,36(1):91-94.
[9]姚静,孔祥东,权凌霄,等.采用蓄能器的快锻液压机建模仿真与试验研究[J].中国机械工程,2009,(2):241-244.
[10]杜巧连,赖振宇,魏建华.压铸机比例节流阀性能测试实验台的设计[J].机械制造,2008,(7):68-70.

Service:
This site has not yet opened Download Service】【Add Favorite
Copyright Forging & Stamping Technology.All rights reserved
 Sponsored by: Beijing Research Institute of Mechanical and Electrical Technology; Society for Technology of Plasticity, CMES
Tel: +86-010-62920652 +86-010-82415085     Fax:+86-010-62920652
Address: No.18 Xueqing Road, Beijing 100083, P. R. China
 E-mail: fst@263.net    dyjsgg@163.com