锻压技术

变截面波纹板冷弯成形过程的有限元模拟研究

英文标题：Research on cold bending process for variable cross-section corrugated plate by finite element simulation

作者：曹俊杰1 刘天慧1 崔晶2

单位：（1.深圳职业技术大学工业训练中心广东深圳 518055 2.深圳职业技术大学本科教育学院广东深圳 518055）

分类号：TG316.3

出版年,卷(期):页码：2025,50(4):147-159

摘要：

摘要：以变截面波纹板为研究对象，利用有限元软件模拟研究了其冷弯成形过程，分析了冷弯成形过程中的等效应力、等效应变分布和应力-应变历程曲线。将顶板分为平板段、过渡段、波纹段3部分，对比分析了各部分典型节点的应力、应变及位移曲线。探讨了波纹板平板段起皱缺陷的产生原因以及工艺参数对起皱缺陷的影响规律。结果表明：在冷弯成形过程中，弯角处及其附近区域的等效应力、等效应变值明显高于其他区域，应重视弯角区域的成形；由于板材的横向金属流动在波纹板波纹段与平板段分布不同，平板段会产生起皱缺陷，起皱缺陷大小主要与过渡段长度有关。该研究可为变截面波纹板冷弯成形的大规模生产提供理论依据。

Abstract: For the variable cross-section corrugated plate, the cold bending process was studied by finite element simulation software， and the equivalent stress and equivalent strain distribution and the stress-strain history curves during the cold bending process were analyzed. Then， the top sheet was divided into three parts of flat section， transition section and corrugated section.And the stress， strain and displacement curves of typical nodes in each part were compared and analyzed.Furthermore， the causes of wrinkle defects in the flat section of corrugated plate and the influences of process parameters on the wrinkle defect area discussed.The results show that during the cold bending process， the equivalent stress and equivalent strain values at the corner area and its vicinity are significantly higher than those in other areas， and the forming of corner area should be paid attention to. Due to the different distribution of the lateral metal flow of plate in the corrugate section and the flat section of corrugated sheet， the wrinkle

defect occurs in the flat section， and the size of wrinkle defect is mainly related to the length of transition section. Thus， this study provides a theoretical basis for the large-scale production of cold bending for variable cross-section corrugated plate.

基金项目：

基金项目:国家自然科学基金资助项目(51801026)

作者简介：曹俊杰(1989-)，男，硕士，实验师

参考文献：

?
［1］冯光，张恒，郜豪杰，等. 波纹辊辊形参数对轧制Cu/Al层合板翘曲的影响
［J］. 锻压技术， 2024， 49(1)：106-113.

Feng G，Zhang H，Gao H J，et al. Influence of corrugated roller profile parameters on warpage of rolled Cu/Al laminates
［J］. Forging & Stamping Technology，2024，49(1)：106-113.

［2］张宏昱，阮金华，林继彬，等. 大轴径比工件辊锻过程宽展变形研究
［J］. 锻压技术， 2023， 48(10): 1-7.

Zhang H Y， Ruan J H， Lin J B， et al. Research on wide stretching deformation of large shaft-to-diameter ratio
［J］. Forging & Stamping Technology，2023，48(10)：1-7.

［3］马旭东，候国东，李昕. 基于响应面法冲压工艺过程图应用研究
［J］. 锻压技术，2024，49(4)：90-96.

Ma X D，Hou G D，Li X. Application research on stamping process drawing based on response surface method
［J］. Forging & Stamping Technology，2024，49(4)：90-96.

［4］李志勇，花魁，徐平安，等. TB6钛合金中央件成形工艺优化及仿真分析
［J］. 锻压技术，2024，49(6)：70-80.

Li Z Y，Hua K，Xu P A，et al. Optimization and simulation analysis on forming process for TB6 titanium alloy main rotor hub
［J］. Forging & Stamping Technology，2024，49(6)：70-80.

［5］Sweeney K，Grunewald U. The application of roll forming for automotive structural parts
［J］. Journal of Materials Processing Technology，2003，132(1-3)：9-15.

［6］戴刚，陈科，刘元铭，等. 预制波纹钢/铝复合板轧制工艺模拟与界面结合性能研究
［J］. 锻压技术，2024，49(1)：114-123.

Dai G， Chen K， Liu Y M， et al. Research on rolling process simulation and interface bonding performance of prefabricated corrugated steel/aluminum composite plates
［J］. Forging & Stamping Technology，2024，49(1)：114-123.

［7］韩蕾，李腾飞. 基于有限元模拟的车用齿轮轴冷墩工艺研究与试验验证
［J］. 锻压技术， 2024， 49(6)：61-69.

Han L，Li T F. Research and experimental verification on cold heading process for automotive gear shaft based on finite element simulation
［J］. Forging & Stamping Technology，2024，49(6)：61-69.

［8］Hiroshi O. Cold-roll Forming Technology
［M］. Beijing：Chemical Industry Press，2008.

［9］Han F，Wang S P. Mechanism of roll-bending forming side wave on variable cross-section
［J］. Journal of Plasticity Engineering，2013，20(5)：117-121.

［10］Duggal N，Ahmetoglu M A，Kinzel G L，et al. Computer aided simulation of cold roll forming-A computer program for simple section profiles
［J］. Journal of Materials Processing Technology，1996，59(1-2)：41-48.

［11］木内学. ロ一ル成形-&世纪ヘの展望
［J］. 塑性と加工，1994， 35(5)：944-948.

Kiuchi M. Roll forming & prospects for the 21st century
［J］. Plasticity and Processing，1994， 35(5)：944-948.

［12］Nefuss G，Gilormini P A. Simplified method for the simulation of cold-roll forming
［J］. International Journal of Mechanical Sciences，1993，35(10)：867-878.

［13］Muthler A，Duster A，Volk W，et al. High order thin-walled solid finite elements applied to elastic spring-back computations
［J］. Computer Methods in Applied Mechanics and Engineering，2006，195(41)：5377-5389.

［14］宋爱军. 冷弯型钢轧辊 CAD/CAM 的研究
［D］. 秦皇岛：燕山大学， 2012.

Song A J. Study on CAD/CAM of Cold Roll Forming Section Steel
［D］. Qinhuangdao：Yanshan University，2012.

［15］蔡中义，刘林，王少辉，等. 连续柔性成形过程控制及CAD软件开发
［J］. 中国机械工程， 2011，22(8): 943-947.

Cai Z Y，Liu L，Wang S H，et al. Process control and CAD software development for continuous flexible forming
［J］. China Mechanical Engineering，2011，22(8)：943-947.

服务与反馈：

【文章下载】【加入收藏】