网站首页期刊简介编委会过刊目录投稿指南广告合作征订与发行联系我们English
变形速率对5 m瓜瓣拉形成形的影响
英文标题:Influence of forming rate on stretch forming for 5 m melon petal
作者:李玉辰 张下陆 谷春杰 白志刚 李林桦 
单位:天津航天长征火箭制造有限公司 
关键词:变形速率 5 m瓜瓣 拉形 力学性能 断裂 
分类号:TG386
出版年,卷(期):页码:2022,47(7):122-126
摘要:

 利用有限元分析方法对5种不同变形速率对5 m球形瓜瓣拉形成形过程的影响进行了分析,预测了零件应力及壁厚分布与变形速率之间的关系。通过试验验证,得到真实拉形条件下变形速率对5 m瓜瓣的成形精度、力学性能等方面的影响。结果表明,变形速率提高对产品的表面质量及型面精度无明显影响。变形速率小于0.3~0.4 mm·s-1时,随着变形速率的提高,产品的力学性能出现波动,下降趋势不明显。变形速率大于0.3~0.4 mm·s-1时,随着变形速率的提高,产品的力学性能明显下降,拉形钳口处出现断裂征兆。为了提高生产效率,可采用平台范围内的变形速率。

 The influences of five different forming rates on stretch forming process for 5 m melon petal were analyzed by finite element analysis method, and the relationship between stress and wall thickness distribution of part and forming rate was predicted. Then, through the experimental verification, the influences of forming rate on forming accuracy, mechanical performances and so on for 5 m melon petal were obtained under the condition of real stretch forming. The results show that the increasing of forming rate has no obvious effect on surface quality and profile accuracy of product. When the forming rate is less than 0.3-0.4 mm·s-1, the mechanical performances of the product fluctuate with the increasing of forming rate, and the downward trend is not obvious. However, when the forming rate is greater than 0.3-0.4 mm·s-1, the mechanical performances of the product decrease significantly with the increasing of forming rate, and there are signs of fracture at the clamp of melon petal. In order to improve the production efficiency, the forming rate within the platform range can be a dopted.

基金项目:
天津市科技支撑项目(17YFZCGX00530)
作者简介:
作者简介:李玉辰(1988-),男,硕士,工程师 E-mail:nxca2004.student@sina.com
参考文献:

 [1]韩金全, 陈石平, 徐龙. 某复杂蒙皮拉形中起皱缺陷的消除[J]. 精密成形工程,2015,7(2):55-59.


Han J Q, Chen S P, Xu L. Elimination of wrinkle defects from a certain complex aircraft skin during stretching[J]. Journal of Netshape Forming Engineering,2015,7(2):55-59.

[2]陈雪, 王瑶, 李明哲. 基于可变型面模具的蒙皮件柔性夹钳拉形技术研究[J]. 机床与液压,2015,43(5):60-62.

Chen X, Wang Y, Li M Z. Research on flexible gripper stretch forming technology for skin parts based on reconfigurable forming die[J]. Machine Tool & Hydraulics,2015,43(5):60-62.

[3]房涛涛, 李晓星,郎利辉. 大厚度双曲度铝合金飞机蒙皮拉伸成形工艺优化[J]. 锻压技术,2021,46(1):29-36,42.

Fang T T,Li X X,Lang L H. Optimization on stretch forming process for hyperbolic aluminum alloy aircraft skin with large thickness [J]. Forging & Stamping Technology,2021,46(1):29-36,42.

[4]谢洪志, 王玲,赵天章,等. 基于数字化的蒙皮拉形加载轨迹优化与应用[J]. 锻压技术,2021,46(1):56-59.

Xie H Z,Wang L,Zhao T Z,et al. Optimization and application of loading trajectory in stretch forming of skin based on digital [J]. Forging & Stamping Technology,2021,46(1):56-59.

[5]张彦敏, 周贤斌. 蒙皮拉形加载轨迹优化[J]. 北京航空航天大学学报,2007, 33(2):201-202.

Zhang Y M, Zhou X B. Optimization of loading trajectory in skin stretch forming process[J]. Journal of Beijing University of Aeronautics and Astronautics,2007, 33(2):201-202.

[6]房娃, 杨程,赵鸿飞,等. 预拉伸变形量对2219铝合金组织与性能的影响[J].机械工程材料,2020, 44(10):38-42.

Fang W, Yang C, Zhao H F, et al. Effect of pre-tension deformation on microstructure and properties of 2219 aluminum alloy[J]. Materials for Mechanical Engineering,2020, 44(10):38-42.

[7]金淳, 黄亮,李建军,等.不同热处理状态下成形速率对2219 铝合金成形极限的影响[J].塑性工程学报,2017,24 (1): 125-132.

Jin C,Huang L,Li J J, et al. Influence of forming rate on forming limit of 2219 aluminum alloy under different heat treatment conditions[J]. Journal of Plasticity Engineering, 2017, 24(1):125-132.

[8]朱浩, 朱亮,陈剑虹,等.不同应力状态下铝合金变形及损伤机理的研究[J]. 稀有金属材料与工程,2007, 36(4):597-601.

Zhu H, Zhu L, Chen J H, et al. The study of deformation and damage mechanism of aluminum alloy (6063) under different stress states[J]. Rare Metal Materials and Engineering,2007, 36(4):597-601.

[9]张冬冬, 王勇,任祥,等.6016铝合金变形应变场研究新方法[J]. 长春工业大学学报,2014, 35(2):206-211.

Zhang D D, Wang Y, Ren X, et al. A new method analyzing 6016 aluminum alloy changing strain field[J]. Journal of Changchun University of Technology, 2014, 35(2):206-211.

[10]刘万辉, 鲍爱莲,崔新. 变形速率对7075铝合金流变应力的影响[J]. 黑龙江科技学院学报, 2005, 15(6):358-360.

Liu W H, Bao A L, Cui X. Effect of s train rates on flow stress feature of 7075 aluminum alloy[J]. Journal of Heilongjiang Institute of Science & Technology, 2005, 15(6):358-360.

[11]张孜昭, 许晓嫦,刘志义,等. 应变速率对强变形Al-Cu合金中析出相低温回溶速度的影响[J]. 黑龙江科技学院学报,2010, 25(2):15-18.

Zhang Z Z, Xu X C, Liu Z Y, et al. Effect of strain rate on redissolution rate of precipitated phase at low temperature in severely plastically deformed Al-Cu alloy[J]. Journal of Heilongjiang Institute of Science & Technology,2010, 25(2):15-18.

[12]刘明朴, 彭晓东,刘军威,等.大塑性变形下变形速率对AZ31合金成形性能的影响[J]. 热加工工艺,2010, 39(21):115-117.

Liu M P, Peng X D, Liu J W, et al. Effect of deformation rate on formability of AZ31 alloy under large plastic deformation[J]. Hot Working Technology,2010, 39(21):115-117.
服务与反馈:
本网站尚未开通全文下载服务】【加入收藏
《锻压技术》编辑部版权所有

中国机械工业联合会主管 北京机电研究所有限公司 中国机械工程学会塑性工程分会主办
联系地址:北京市海淀区学清路18号 邮编:100083
电话:+86-010-82415085 传真:+86-010-62920652
E-mail: fst@263.net(稿件) dyjsjournal@163.com(广告)
京ICP备07007000号-9