网站首页期刊简介编委会过刊目录投稿指南广告合作征订与发行联系我们English
不同斜置角度的液压机刚度分析与本体优化设计
英文标题:Analysis on hydraulic press stiffness with different oblique angles and optimization design of body
作者:胡开广 仇平 郑学斌 王宝川 韩龙帅 杨建伟 
单位:首钢技术研究院 燕山大学 
关键词:双柱液压机 斜置角度 预紧力 偏心载荷 有限元优化 
分类号:TG386
出版年,卷(期):页码:2019,44(4):113-120
摘要:

根据行业标准JB/T 122292015,双柱液压机的斜置角度分为22°,25°,30°,32.5°和35°。不同的斜置角度改变了液压机的本体几何参数,也改变了液压机的重量。以5 MN公称压力双柱上推式液压机本体为研究对象,以液压机斜置角度为变量,以强度和刚度为约束条件,以减小本体重量为目标,利用ANSYS Workbench有限元软件,进行本体优化设计。在立柱与横梁接触面处不发生开缝现象的条件下,模拟计算了中心载荷和偏心载荷下的最小预紧力,分析得到斜置角度对液压机预紧力的影响规律。通过上述分析结果,研究了斜置角度对液压机的重量的影响趋势,为企业选择双柱液压机的规格提供了理论指导。

 

According to the industry standard JB/T 12229—2015, the oblique angles of double-column hydraulic press were divided into 22°, 25°, 30°, 32.5° and 35°, respectively, the geometry parameters of hydraulic press body were changed by different oblique angles, and the weight of hydraulic press was also changed. For the body of double-column push-up hydraulic press with 5 MN nominal pressure, taking the oblique angle of hydraulic press as the variable, the strength and stiffness as the constraint conditions and reducing the weight of body as the goal, the design of body was optimized by finite element software ANSYS Workbench. Under the condition that no slotting occurs on the contact surface between column and cross beam, the minimum pre-tightening force under the center load and the eccentric load was simulated and calculated, and the influence rule of oblique angle on the pre-tightening force of hydraulic press was analyzed. Through the above analysis results, the influence trend of oblique angle on the weight of hydraulic press was studied. Thus the theoretical guidance for enterprises to choose the specifications of double-column hydraulic press is provided.

 

基金项目:
燕山大学先进制造成形技术及装备国家地方联合工程研究中心项目(yd201613)
作者简介:
胡开广(1989-),男,硕士,工程师 E-mail:564471005@qq.com 通讯作者:仇平(1969-),男,博士,教授 E-mail:qiuping@ysu.edu.cn
参考文献:

[1]陈兆生. 基于有限元的快锻液压机工作缸结构改进及优化[J]. 液压与气动, 2010(8):87-89.


Chen Z S. Structural improvement and optimization of the hydraulic cylinder for high speed forging hydraulic press based on finite element method [J]. Chinese Hydraulics & Pneumatics, 2010, (8):87-89.


[2]郭玉玺. 现代自由锻造液压机的技术经济性分析——从锻件生产经济性要求看自由锻造液压机的发展趋势 [J]. 科技创新与生产力, 2010, (12):51-56.


Guo Y X. Technical and economic analysis on modern free forging hydraulic press-development trend of free forging hydraulic press based on economic requirements of forging production [J]. Sci-tech Innovation and Productivity,2010, (12):51-56.


[3]赵升吨,张鹏,范淑琴,等. 智能锻压设备及其实施途径的探讨[J].锻压技术,2018,43(7):32-48.


Zhao S DZhang PFan S Qet al. Discussion on intelligent forging equipment and approaches of its implementation [J]. Forging & Stamping Technology2018,43(7):32-48.


[4]俞新陆. 液压机的设计与应用[M]. 北京:机械工业出版社, 2007.


Yu X L. Design and Application of Hydraulic Press [M]. Beijing: China Machine Press, 2007.


[5]仇平.5 MN双柱上推式快锻液压机本体结构设计与优化[D]. 秦皇岛: 燕山大学, 2014.


Qiu P. Design and Optimization of the Body Structure of 5 MN Double-column Up-thrust Hydraulic Press [D]. Qinhuangdao: Yanshan University, 2014.


[6]吴生富, 金淼, 聂绍珉,. 大型锻造液压机全预紧组合机架的整体性及影响因素分析[J]. 塑性工程学报, 2006, 13(2): 110-113.


Wu S F, Jin M, Nie S M, et al. Integrity and influencing factors analysis of fully preloaded composite frame for large-scale forging hydraulic press [J]. Journal of Plastic Engineering, 2006, 13(2): 110-113.


[7]王春辉, 赵升吨, 谢嘉. 大型快锻液压机法兰支撑液压缸优化设计及参数敏感性分析[J]. 锻压装备与制造技术, 2009, 44(2): 42-45.


Wang C H, Zhao S D, Xie J. Optimization design and parameter sensitivity analysis of flange supporting hydraulic cylinder of large quick forging hydraulic press [J]. China Metalforming Equipment & Manufacturing Technology, 2009, 44(2): 42-45.


[8]陈罗, 梁基照. 复合形法在法兰支承液压缸优化设计中的应用[J]. 机械设计与制造, 2010,(3): 82-84.


Chen L, Liang J Z. Application of composite shape method in optimal design of flange-supported hydraulic cylinder [J]. Machinery Design and Manufacturing, 2010,(3):82-84.


[9]张大可, 孙圣权. 液压机下横梁结构拓扑的进化结构优化[J]. 重庆大学学报, 2009, 32(10): 1117-1121.


Zhang D K, Sun S Q. Evolutionary structure optimization of lower beam structure topology of hydraulic press [J]. Journal of Chongqing University, 2009, 32(10): 1117-1121.


[10]JB/T 122292015,油泵直接传动双柱斜置式自由锻造液压机[S].


JB/T 122292015,Double-column oblique type open-die forging hydraulic press with direct drive of oil pump [S].


[11]吴生富. 150 MN锻造液压机[M]. 北京: 机械工业出版社, 2012.


Wu S F. 150 MN Hydraulic Forging Press [M]. Beijing: China Machine Press, 2012.


[12]金淼, 董晓传, 邹宗园, . 给定预紧力下组合机架的上限载荷计算[J]. 中国机械工程, 2012, 23(20): 2476-2480.


Jin M, Dong X C, Zou Z Y, et al. Calculation of upper limit load for assembled frame hydraulic press under given pre-tightened force [J]. China Mechanical Engineering, 2012, 23(20): 2476-2480.


[13]郭宝峰, 于琳琳, 金淼. 预应力组合下横梁临界预紧力影响因素研究[J]. 中国机械工程, 2013, 24(19): 2567-2572.


Guo B F, Yu L L, Jin M. Study on the influence factors of critical pretension of prestressed composite lower beam [J]. China Mechanical Engineering, 2013, 24(19): 2567-2572.


[14]段志东, 苏铁明. 组合机架的刚度分析和拉杆预紧力研究[J]. 机械科学与技术, 2009, 28(4):450-454.


Duan Z D, Su T M. Stiffness analysis of combined frame and preload of tie rod [J]. Journal of Mechanical Science and Technology, 2009, 28(4):450-454.




 

服务与反馈:
本网站尚未开通全文下载服务】【加入收藏
《锻压技术》编辑部版权所有

中国机械工业联合会主管 北京机电研究所有限公司 中国机械工程学会塑性工程分会主办
联系地址:北京市海淀区学清路18号 邮编:100083
电话:+86-010-82415085 传真:+86-010-62920652
E-mail: fst@263.net(稿件) dyjsjournal@163.com(广告)
京ICP备07007000号-9