锻压技术

冲裁过程中压边力对成形质量的影响

英文标题：Influence of blank holder force on forming quality during blanking

作者：岳学虎樊瑜瑾郑淮和吴家喜

分类号：TG386.2

出版年,卷(期):页码：2018,43(4):53-59

摘要：

运用DEFORM-3D软件，对304不锈钢板料冲裁过程中产生的等效应力、等效应变以及材料流动特性进行了有限元模拟，研究了不同压边力作用下冲裁过程中板料的变形过程以及压边力对断面轮廓的影响，得到板料冲裁过程中的冲裁力-行程曲线和冲裁件断面图。通过MATLAB软件拟合分析发现：当作用在板料上的压边力较小时，圆角带长度、宽度、锥度和毛刺长度随着压边力的增大而减小；当作用在板料上的压边力超过某一临界值时，圆角带长度、宽度、锥度和毛刺长度随着压边力的增大而增大。最后通过实验对有限元模拟结果进行验证，在实际生产中选用合适的压边力可以提高冲裁件的断面质量。

The equivalent stress, equivalent strain and material flow characteristics during the blanking process of stainless steel 304 sheet were finite element simulated by software DEFORM-3D, and the influences of deformation process and blank holder forces of sheet metal on the cross section contour during the blanking process were studied under different blank holder forces. Then, the blanking force versus stroke curve and the cross section drawing of blanking pieces during the blanking process of sheet metal were gained. Through the MATLAB software fitting analysis, when the blank holder force acting on the sheet metal is small, the fillet belt length, width, taper and burr length decrease with the increasing of blank holder force, but when the blank holder force acting on the sheet metal exceeds a critical value, the fillet belt length, width, taper and burr length increase with the increasing of blank holder force. Finally, the finite element simulation results were verified by experiments, and the appropriate blank holder force should be selected to improve the cross section quality of blanking pieces in the actual production.

基金项目：

昆明理工大学分析测试基金（2017M20162103009）

岳学虎（1992-），男，硕士研究生；E-mail：timeyuehu@163.com；通讯作者：樊瑜瑾（1962-），男，博士，教授；E-mail：fanyujinkmust@163.com

参考文献：

[1]王蕾, 苏娟华, 胡道春. 毛坯压边对冲裁过程影响的研究[J]. 锻压装备与制造技术, 2005, 40(3):67-68.

Wang L, Su J H, Hu D C. The research of the influence of the blank holding on punching[J]. China Metalforming Equipment & Manufacturing Technology, 2005, 40(3):67-68.

[2]温莉敏, 许树勤. 压边力对精冲质量影响的有限元分析[J]. 淮海工学院学报：自然科学版, 2015, 24(2):6-9.

Wen L M, Xu S Q. Finite element analysis of the influence of blank-holder force on fine-blanking quality[J]. Journal of Huaihai Institute of Techology：Natural Science Edition, 2015, 24(2):6-9.

[3]姚敏茹, 万宏强, 李福援. 机械零件毛刺控制及去除工艺现状[J]. 新技术新工艺, 2005, (12):20-22.

Yao M R, Wan H Q, Li F Y. Present status of burr control and debarring process on mechanical elements [J]. New Technology and New Process, 2005, (12):20-22.

[4]刘忠利. 浅谈机械零件毛刺控制及去除工艺现状研究[J]. 中国科技财富, 2012, (9):136.

Liu Z L. Research on burr control and removal process of mechanical parts[J]. Fortune World, 2012, (9):136.

[5]陈启东, 温华兵. 基于Deform-2D的薄板冲裁有限元分析[J]. 机械设计与制造, 2012, (5):98-100.

Chen Q D, Wen H B. Finite elements analysis for sheet stamping process based on Deform-2D[J]. Machinery Design & Manufacture, 2012, (5):98-100.

[6]谢晖, 杨旭静, 成艾国,等. 计算机仿真中板料冲压成形压边力的优化[J]. 中国机械工程, 2002, 13(22):1910-1914.

Xie H, Yang X J, Cheng A G, et al. Optimization of binder force during computer simulation of sheet metal forming[J]. China Me-chanical Engineering, 2002, 13(22):1910-1914.

[7]孙成亮. 平面压边半精冲工艺成形参数优化及实验研究[D]. 重庆：重庆理工大学, 2011.

Sun C L. Forming Parameters Optimization and Experimental Study of Flat Blank Semi Fine Blanking Process[D]. Chongqing: Chongqing University of Technology, 2011.

[8]潘艺果, 夏巨谌, 谢世坤. 压边力在板料冲压成型中的控制研究[J]. 机械工程师, 2004, (1): 61-64.

Pan Y G, Xia J C，Xie S K. The research of BHF control in sheet metal forming [J]. Mechanical Engineer, 2004, (1):61-64.

[9]郑海涛. 不锈钢板冷冲过程及其成形质量影响因素研究[D]. 昆明：昆明理工大学, 2017.

Zheng H T. Study on the Cold Stamping Process of Stainless Steel Plate and the Influencing Factors of Forming Quality[D]. Kunming: Kunming University of Science and Technology, 2017.

[10]李其钒, 潘燕, 王锐,等. 影响冲裁零件质量的原因分析[J]. 热加工工艺, 2011, 40(7):88-90.

Li Q F, Pan Y, Wang R, et al. Reason analysis on influencing quality of punching parts [J]. Hot Working Technology, 2011, 40(7): 88-90.

[11]柯桂颜, 路平, 石婧,等. 拉延筋、压边力对冲压件成形性能的影响研究[J]. 锻压技术, 2016, 41(5):39-43.

Ke G Y, Lu P, Shi J, et al. Influences of drawbead and blank holder force on formability of stampings[J]. Forging & Stamping Technology, 2016, 41(5):39-43.

[12]张晓斌, 孙宇, 樊红梅,等. 板料成形压边力控制技术研究现状及发展趋势[J]. 锻压技术, 2007, 32(6):6-12.

Zhang X B, Sun Y, Fan H M, et al. Recent research and development trend of blank holder force control technology for sheet metal forming [J]. Forging & Stamping Technology, 2007, 32(6):6-12.

[13]马朝兴. 冲压工艺与模具设计[M]. 北京：化学工业出版社, 2007.

Ma C X. Stamping Process and Die Design[M]. Beijing: Chemical Industry Press, 2007.

服务与反馈：

【本网站尚未开通全文下载服务】【加入收藏】