锻压技术

TA18钛合金导管的内径滚压连接工艺

英文标题：Internal rolling connecting on guide tubes for titanium alloy TA18

作者：张荣霞吴为曾元松

单位：中国航空工业集团公司北京航空制造工程研究所塑性成形技术航空科技重点实验室数字化塑性成形技术及装备北京市重点实验室

关键词：28 MPa液压系统 TA18钛合金钛合金导管内径滚压连接成形扭矩痕迹法

分类号：TG386

出版年,卷(期):页码：2017,42(5):43-47

摘要：

针对TA18钛合金导管开展了内径滚压连接工艺研究，研制了基于扭矩控制的滚压连接专用设备，实现了难变形钛合金导管的内径滚压连接成形；同时掌握了成形扭矩与连接件管端伸出量和连接件内径的关系，指出管端伸出量和连接件内径与成形扭矩呈线性递增关系，确定了最佳成形扭矩；采用痕迹法作为连接组件配合面密接度的检测试验方法，检测结果表明，管套与堵头之间的密封面沿圆周无间断，密接度达到100%。所研制的钛合金导管内径滚压连接件通过了配合面密接度检测和28 MPa液压系统性能验证，达到了28 MPa液压系统的性能要求。

For the TA18 titanium alloy, the internal rolling connecting of guide tubes was researched. Then, the special equipment based on torque control was developed, and the internal rolling connecting of titanium alloy guide tubes with difficulty in deformation was realized. At the same time, the relationships between the forming torque and the protrusion of tube end as well as the internal diameter of connecting tube were mastered to point out their linear increase approximately, and the detection on tightening degree between mating surfaces of the union parts was carried out by the track method. The detection result indicates that the tightening degree is up to a hundred percent between the mating surfaces of tube and plug with uninterrupted circumference. Furthermore, the produced parts are tested by tightening degree of mating surface and hydraulic system 28 MPa to meet the performance requirements.

基金项目：

总装预研航空支撑项目（61901110302）

张荣霞（1979-），女，硕士，高级工程师

参考文献：

［1］曾元松, 李志强. 连接管件的先进塑性成形技术试验研究[J]. 金属成形工艺, 2003, 21(3):4-7.Zeng Y S, Li Z Q. Experimental investigation of the advanced forming technology of tubular parts [J].Metal Forming Technology, 2003, 21(3):4-7.
［2］吕昕宇, 张士宏, 许沂,等. 连接管件内径滚压成形有限元模型的建立及分析[J]. 塑性工程学报, 2005, 12(1):85-88.Lyu X Y, Zhang S H, Xu Y, et al．Models of FEM simulation on roller inner swaging of connecting tubes and analysis [J]. Journal of Plasticity Engineering, 2005, 12(1):85-88.
［3］Zeng Y S. Finite element simulation and experimental research on the internal rolling connection for titanium alloy tubes [J]. Materials Science Forum, 2005, 475-479(1):3287-3290.
［4］焦裕松，焦宗夏，范开华. 航空液压技术发展研究[A]. 航空科学技术学科发展报告(2008-2009) [C]. 北京，2009.Jiao Y S, Jiao Z X, Fan K H. Research of the aviation hydraulic pressure technics development [A]. The Report of Aviation Science Technics Development (2008-2009) [C]. Beijing，2009.
［5］董营，张进生，王志，等. 铜管三辊行星轧制过程轧辊轴力学行为分析[J]. 热加工工艺, 2016，45(5):111-115.Dong Y, Zhang J S, Wang Z, et al. Analysis on mechanical behavior of roll-shaft during three-roll planetary rolling process of copper tube[J]. Hot Working Technology, 2016，45(5):111-115.
［6］封骥. 铜铝复合板轧制力的研究[D]. 沈阳：沈阳工业大学, 2016.Feng J. Research on Rolling Force of the Copper Aluminum Composite Plate [D]. Shenyang: Shenyang University and Technology, 2016.
［7］王光艳，梅益，陈浪，等. 42CrMo环件轧制成形的数值模拟与分析[J]. 锻压技术, 2014, 39(5):82-86.Wang G Y, Mei Y, Chen L, et al. Numerical simulation and analysis of rolling forming of 42CrMo rings [J]. Forging Stamping Technology, 2014, 39(5):82-86.
［8］张英凤. 炉卷轧机轧制过程力学分析及其机架结构强度的研究[D]. 鞍山:辽宁科技大学, 2014.Zhang Y F. Study on Mechanical Analysis and Frame Structural Strength of Stickle Mill Rolling [D]. Anshan: University of Science and Technology Liaoning, 2014.
［9］李冰, 杨志, 刘化民,等. 三辊行星轧制运动和管坯变形规律的仿真模拟[J]. 塑性工程学报, 2005, 12(5):70-73.Li B, Yang Z, Liu H M, et al. Computer simulation on the movement and deformation rules of three-roll planetary rolling process of copper tube [J]. Journal of Plasticity Engineering, 2005, 12(5):70-73.
［10］GJB 3230—98, 航空液压导管和接头试验方法[S].GJB 3230—98, Aircraft hydraulic system—Test methods for tube/fitting assemblies[S].
［11］李俊升. 28 MPa导管连接件标准研究[J]. 航空标准化与质量, 1999,(4):5-8.Li J S. Study on the 28 MPa tube connector technical standard [J]. Aviation Standardization and Qulity, 1999,(4):5-8.

服务与反馈：

【本网站尚未开通全文下载服务】【加入收藏】