|
With the deeper research on vibration of cold rolling roll, it was found that most of types of the vibration happened on the work rolls was the coupled vibration. Firstly, the simplified vibration model of the main drive system and the rolls were established, and their natural frequencies were calculated by software Matlab. Then, the dynamic simulation of rolls was conducted by software Adams, and interfering force and torque in three times vibration frequency were added during the simulation process. The simulation shows that without the outer interference, self-excited vibration occurs in cold rolling mill because of the friction between the rolls; for the six rolling mill, the horizontal vibration of the middle roll has impacts on the vertical vibration and the torsional vibration of work rolls. When the vertical vibration and the torsional vibration occur at the same time, the vibration of work rolls shows the characteristics of other vibrations.
|
|
［1］杨旭,童朝男.板带轧机振动问题研究[J].钢铁研究学报,2009,21(11):1-4.Yang X, Tong Z N. Chatter in rolling mill[J].Journal of Iron and Steel Research,2009,21(11):1-4.
［2］侯福祥,张 杰,曹建国.带钢冷轧机振动问题的研究进展及评述[J].钢铁研究学报,2007,19(10):6-11.Hou F X, Zhang J, Cao J G. Review of chatter studies in cold rolling [J]. Journal of Iron and Steel Research, 2007,19(10):6-11.
［3］闫晓强,王辉,周杰,等.现代连轧机耦合振动抑制重要进展[J].中国冶金,2014,24(4):1-4.Yan X Q, Wang H, Zhou J, et al. Important progress of coupling vibration inhibition on modern tandem mill [J].China Metallurgy，2014,24(4)：1-4.
［4］张帅,吴炳胜. 冷连轧机主传动系统的扭转振动分析[J]. 锻压技术, 2015，40(5):96-98.Zhang S, Wu B S. Torsional vibration analysis on the main drive system of tandem cold rolling mill [J]. Forging & Stamping Technology, 2015，40(5):96-98.
［5］吴继民.CSP热连轧机振动问题分析[D].邯郸：河北工程大学,2012.Wu J M. Vibration Analysis of CSP Hot Strip Mill [D]. Handan: Hebei University of Engineering, 2012.
［6］吴炳胜, 李运强, 吴继民.CSP热连轧机垂直振动建模分析[J]. 锻压技术, 2014, 39(1): 91-94.Wu B S, Li Y Q, Wu J M. Simulation and analysis on vertical vibration of CSP hot strip mill [J]. Forging & Stamping Technology, 2014，39(1):91-94.
［7］陈海周.冷轧带钢轧机振动测试及振纹研究[D].重庆：重庆大学,2010.Chen H Z. Vibration Measurement of Cold Rolling Mill and Study of Chatter Mark [D]. Chongqing: Chongqing University,2010.
［8］孟令启,马金亮,黄其柏.基于Matlab的4200轧机垂直振动仿真[J].钢铁研究学报,2007,19（7）：58-62.Meng L Q, Ma J L, Huang Q B. Vertical vibration simulation of 4200 mill based on Matlab[J].Journal of Iron and Steel Research, 2007,19（7）：58-62.
［9］殷萍.SG18辊轧机辊系特性的研究[D].北京：北京科技大学，2003.Yin P. Study on the Characteristics of the Roll System of SG18-h Mill[D].Beijing: University of Science and Technology Beijing,2003.
［10］刘力,岳海龙,邹家祥.高速冷轧机辊缝摩擦系数影响因素的研究[J].重型机械，2001,(2):9-12.Liu L, Yue H L, Zou J X. The study on gap friction coefficient influencing factors high-speed mill roll [J].Heavy Machinery,2001, (2):9-12.
|
