锻压技术

大型厚壁椭圆封头多次热冲压成形分析

英文标题：Analysis of multi-hot stamping forming for large thick-wall ellipse head

作者：陈帅峰王守东雷玉川刘劲松张士宏

关键词：封头多次热冲压有限元成形载荷

分类号：TG316

出版年,卷(期):页码：2015,40(2):37-40

摘要：

采用有限元法对大型厚壁椭圆封头的一次和多次热冲压成形工艺进行数值模拟。对比分析厚壁封头在两种成形工艺下的压机成形载荷和封头成形壁厚的差异，并研究不同凹模直径对封头多次成形载荷和壁厚的影响。研究结果表明，多次热冲压可以有效地降低封头的成形载荷60%左右。多次热冲压封头壁厚比一次成形稍有减薄，但最大减薄率为5.9%，在合理要求范围内。通过与相近规格封头进行实验对比，壁厚分布规律相一致，因此能够达到较好地预测成形的目的。

Once and multi-hot stamping processes of large thick-wall elliptical head were numerically simulated by finite element method.The differences of hydraulic press forming load and thickness of the head from the two forming processes were analyzed comparatively, and the influence of different die radius on the forming load and thickness was studied. The results show that multi-hot stamping can effectively reduce the forming load to 60%. The thickness of the heads formed by multi-hot stamping is slightly thinner than that of the heads formed by one time stamping, but the biggest thinning rate is 5.9% which is in a reasonable range. Compared with the head of similar specifications, wall thickness distribution is consistent, and the goal of a better prediction of thick-wall head forming can be achieved.

基金项目：

河南省科技开放合作项目（142106000021）

陈帅峰（1987-）男，硕士研究生张士宏（1962-）男，博士，研究员，博士生导师

参考文献：

［1］蒋起臣,王永生,杨一平,等.小口径厚壁球形封头的冷拉深成形[J].锻压技术，2013,38(2):40-42.Jiang Q C, Wang Y S, Yang Y P, et al. Cold drawing of small-bore thick walled spherical head[J]. Hot Working Technology, 2013,38(2):40-42.
［2］李海峰,陈明亮,谢志毅.大型厚壁半球形封头热冲压成形的数值模拟[J].计算机仿真, 2004,21（3）：109-112. Li H F, Chen M L, Xie Z Y. Numerical simulation of hot drawing process for a large-scale thick-walled semi-spherical head [J]. Computer Simulation, 2004,21（3）：109-112.
［3］安红萍,刘建生,郭玉茹,等.大型厚壁半球形封头成形的模拟与实验研究[J].锻压技术,2009,34（5）：135-138.An H P, Liu J S, Guo Y R, et al. Numerical simulation and experimental research of lager thick-wall semisphere head forming[J].Forging & Stamping Technology, 2009,34(5):138-138.
［4］张国智.大型封头热拉深力学机理及仿真研究[J].中国机械工程，2013,24（8）:1114-1117.Zhang G Z. Study on mechanics mechanism and simulation of hot-drawing process of large head[J].China Mechanical Engineering，2013,24（8）:1114-1117.
［5］周朝辉,曹海桥.厚壁椭圆形封头热拉深成形及有限元模拟[J].热加工工艺,2004,6(5):44-45.Zhou C H, Cao H Q. Hot drawing and finite element simulation of thick-wall ellipse end socket [J].Hot Working Technology, 2004,6(5):44-45.
［6］杨晓禹.特大型封头锻造新工艺[D].秦皇岛:燕山大学,2008. Yang X Y. Study on New Process of Oversize Head Forging [D].Qinhuangdao: Yanshan Unversity, 2008.
［7］刘攀.特大型封头的锻造成型工艺研究[D].重庆:重庆大学,2011. Liu P. Study on Forging Process of Oversize and Thick Wall Head [D].Chongqing: Chongqing Unversity,2011.
［8］Kirby D S, Wild P M. Deep drawing of press vessel end closures: Finite element simulation and validation [J]. Journal of Materials Processing Technology, 2000, 103:247-260.

服务与反馈：

【本网站尚未开通全文下载服务】【加入收藏】