网站首页期刊简介编委会过刊目录投稿指南广告合作征订与发行联系我们English
直驱式泵控电液伺服系统建模与动态特性分析
英文标题:Modeling and dynamic characteristics analysis of direct drive pump-controlled electro-hydraulic servo system
作者:郑洪波 孙友松 黎勉 冼灿标 
单位:广东工业大学 
关键词:电液伺服系统 动态特性 建模 泵控 
分类号:TH137.1
出版年,卷(期):页码:2011,36(5):66-70
摘要:

为研究直驱式泵控电液伺服系统的动态特性,分析了系统的工作原理,分别建立了泵控和阀控两种控制系统的数学模型并进行了动态响应的理论分析和比较研究。搭建了一个包含交流伺服电机定量泵为动力源的伺服驱动系统实验台,可以进行两种控制系统的性能实验。对实验系统进行了动态响应的数字模拟和实验研究,结果表明,由于泵控系统液压固有频率较低,动态响应慢,上升时间为阀控系统的8倍。在研究的基础上提出了提高该类系统动态特性的措施。
 

In order to study the dynamic characteristics of direct drive pump\|controlled electro\|hydraulic servo system , the working principle of the system was analyzed, and the mathematical models of pump\|controlled system and valve\|controlled system were built to carry out theoretical analysis and comparative research of dynamic response. A servo drive system laboratory bench was set up taking AC servo motor and fixed displacement pump as the power source,on which both control systems performance can be tested. The numeral simulation and the experimental study of dynamic response for the experiment system were done. The result shows that the rise time of the pump\|controlled system is 8 times longer than that of the valve\|controlled system because of its low hydraulic natural frequency and slow dynamic response. On the basis of the research, the measures to improve the dynamic characteristics of such systems were put forward.
 

基金项目:
广东省科技计划项目(2006B11901004)
作者简介:
参考文献:

[1]涂婉丽. 直驱式容积控制电液伺服系统动态特性的研究[D]. 哈尔滨:哈尔滨工业大学,2005.

[2]郭建宇. 无阀电液伺服系统的建模与仿真研究[D]. 大连:大连理工大学,2005.

[3]何寄平. 泵控伺服液压机液压系统研究[D].广州:广东工业大学,2010.

[4]黎勉,罗勇武. 交流变频调速在液压系统中的应用[J]. 机床与液压,1997,(6):16-17.

[5]郑洪波,孙友松. 直驱式容积控制电液伺服系统及其发展现状[J].机床与液压,2011, 39(2):132-136.

[6]中央电大《液压传动辅导教材》编写小组. 液压传动辅导教材[M]. 北京:中央广播电视大学出版社,1986.

[7]田逸,Thomas A Lipo. 基于MATLAB软件的交流永磁同步电机调速系统研究[J].江苏电器,2008,(12):26-30.

[8]姚舜才,温志明,黄刚. 运动控制系统分析与应用[M]. 北京:国防工业出版社,2008.

[9]李永堂,雷步芳,高雨茁. 液压系统建模与仿真[M]. 北京:冶金工业出版社, 2003.

[10]杨玉涛,张小栋.高速电磁阀模型建立及响应特性研究[J]. 测控技术,2008,27(6):86-89.

[11]任杉,李玮,韩青. 基于MATLAB的阀控缸伺服系统仿真分析[J]. 装备制造技术,2009,(9):32-33.

 

服务与反馈:
本网站尚未开通全文下载服务】【加入收藏
《锻压技术》编辑部版权所有

中国机械工业联合会主管  中国机械总院集团北京机电研究所有限公司 中国机械工程学会主办
联系地址:北京市海淀区学清路18号 邮编:100083
电话:+86-010-82415085 传真:+86-010-62920652
E-mail: fst@263.net(稿件) dyjsjournal@163.com(广告)
京ICP备07007000号-9