网站首页期刊简介编委会过刊目录投稿指南广告合作征订与发行联系我们English
AZ80镁合金拔长工艺及锻后力学性能研究
英文标题:Research on forging-out and mechanical properties after forging of AZ80 magnesium alloy
作者:邓子玉 陈献刚 王华文 崔建忠 
单位:东北大学 沈阳理工大学 
关键词:铸态镁合金 拔长工艺 力学性能 
分类号:TG356
出版年,卷(期):页码:2011,36(1):17-20
摘要:

研究了铸态AZ80镁合金拔长工艺,并对锻造后工件在室温及高温条件下进行了力学性能测试。结果表明:温度、变形速率、道次压下量及进给量对镁合金成形影响很大,合理控制工艺参数,能够得到理想的锻造结果。室温条件下,随着锻比的增加,抗拉强度在逐渐升高;在250,300,350和370 ℃的拉伸温度下,抗拉强度依次为103.5,54.7,26.6和18.4 MPa,塑性在250~300 ℃时升高,350~370 ℃时其塑性开始下降。

Forging-out of the as-cast AZ80 magnesium alloy was researched and the main mechanical properties target were tested at room temperature and high temperature. The results show that the temperature, deforming rate, each pass pressing download and feeding length of each time have a great influence on the deformation of the magnesium alloy. The reasonably technology parameter control can obtain the ideal forging result. At room temperature ,the strength increases with the increasing of forging ratio. Under the tensile temperatures of 250,300,350 and 370 ℃, the according strengths would be shown as 103.5,54.7,26.6 and 18.4 MPa. The plasticity raised during the temperature of 250-300 ℃, but went down during 350-370 ℃.

基金项目:
辽宁省创新团队项目(2009T084);沈阳市重点实验室项目(1081101-1-00)
作者简介:
参考文献:


[1]  郭鸿镇.合金钢与有色合金锻造[M].第1版.西安:西北工业大学出版社,1999.
[2]  吕炎.锻件组织性能控制[M].第1版.北京:国防工业出版社,1988.
[3]  陈振华.变形镁合金[M].第1版.北京:化学工业出版社,2005.
[4]  Sitdikov O,Sakai T,Goloboradko A,et al.Grian fragmentation in a coarse-grained 7475 Al alloy during hot deformation[J].Scr,Mater,2004,51:175.
[5]  Belyakov A,Sakai T,Miura H.Fine-grained structure formation in Austeniticstainless steel under multiple deformation at 0.5 Tm[J].Materials Transaction,2000,41(4):476-484.
[6]  Valiev R Z,Islamgaliev R K,Alexandrov I V.Bulk nanostructured materials from severe plastic deformation[J].Progress of Materials Science,2000,45(2):103-189.
[7]  郭强,严红革,陈振华,等.多向锻造工艺对AZ80镁合金显微组织和力学性能影响[J].金属学报,2006,42(7):739.
[8]  杨乐.多向锻造对ZK60镁合金组织与性能的影响[D]. 哈尔滨:哈尔滨工业大学,2009.
[9]  周顺新.铸态ZK60、AZ80镁合金锻造技术研究[D].沈阳:沈阳理工大学,2010.
[10]  何文武,郭会光,刘建生.锻造裂纹的分析与防治[J].锻压技术,2010,35(1):16-19.
[11]  张青来,胡永学,王粒粒. AZ31 B镁合金拉伸应力-应变和再结晶组织[J].稀有金属材料与工程,2008,37(4):678-681.

 

服务与反馈:
本网站尚未开通全文下载服务】【加入收藏
《锻压技术》编辑部版权所有

中国机械工业联合会主管 北京机电研究所有限公司 中国机械工程学会塑性工程分会主办
联系地址:北京市海淀区学清路18号 邮编:100083
电话:+86-010-82415085 传真:+86-010-62920652
E-mail: fst@263.net(稿件) dyjsjournal@163.com(广告)
京ICP备07007000号-9