锻压技术

环件摆辗镦粗过程中的塑性铰特性

英文标题：Plastic hinge feature in rotary forging and upsetting process of ring billet

作者：张福芳王华君汪小凯黄强曾杰彭毅

关键词：环件摆辗镦粗塑性铰高径比有限元

分类号：TG316.11

出版年,卷(期):页码：2010,35(2):141-143

摘要：

塑性铰是影响环件摆动辗压工艺稳定的重要因素,研究其形成过程非常必要。建立了基于ABAQUS软件的环件摆辗镦粗有限元模型,研究了环件塑性铰区域的应力分布状况,分析了不同高径比对环形件塑性铰区域应力场的影响,得到了塑性铰形成的影响因素及变化规律,即随着环件高径比增大,塑性铰的位置沿摆头旋转方向偏移,促进了环件摆辗镦粗工艺的稳定与发展。

The plastic hinge is the key factor that can effect the stability of the ring rotary forging process and it is essential to study the feature of the plastic hinge.Based on the ABAQUS simulation software,the FE model of ring rotary forging process was established and the stress distribution in the zone of the ring plastic hinge was investigated.The influence mode of ring ratio of height to diameter to the stress distribution in the ring plastic hinge zone was analysed.So the influencing factors and the variation patterns of the establishment and development of the plastic hinge were obtained during ring rotary forging process.That is as high-diameter ratio of ring increases,the location of the plastic hinge shifted along the direction of the rocker's rotation.The above results will promote the stability and development of the ring rotary forging process.

基金项目：

湖北省自然科学基金(2007ABA214);; 国家科技支撑计划(2006BAF04B06);; 材料成形与模具技术国家重点实验室开放基金(06-5)

参考文献：

[1]张文元,张耀春.高层钢结构双重非线性分析的塑性铰法[J].哈尔滨建筑大学学报,2000,33(6):1-7. [2]Johnson,Wineedham G.Plastic hinges in ring indentation inrelation to ring rolling[J].Int.J.Mech.Sci.,1968,10(2):487-490. [3]张猛,胡亚民.摆辗技术[M].北京:机械工业出版社,1998. [4]张猛.环件摆动辗压力计算[J].热加工工艺,1988,17(3):15-21. [5]张猛.计算摆辗压力、扭矩及功率的诺莫图[J].锻压机械,1985,(2):20-21. [6]王广春,赵国群,吕炎.环形件摆动辗压变形机理三维刚塑性有限元分析[J].塑性工程学报,1999,6(4):80-85. [7]程培元,胡锐,卢志国.直齿圆锥齿轮摆辗成形最大辗压力的有限元研究[J].锻压技术,2008,33(1):50-52. [8]Jiang Z Y,Tieu A K.A 3-D finite element method analysisof cold rolling of thin strip with friction variation[J].Tri-bology International,2004,37(2):185-191.

服务与反馈：

【本网站尚未开通全文下载服务】【加入收藏】