|
H型钢热连轧过程的金属变形分析
|
|
英文标题：Metal deforming analysis of H-beam in hot-continuous-rolling process |
|
作者：张波 张勤河 张海龙 陈举华 |
|
单位：山东大学机械工程学院 |
|
关键词：H型钢 连轧 变形分析 数值模拟 |
|
分类号：TG335.4 |
|
出版年,卷(期):页码：2009,34(3):88-91 |
|
摘要：
|
|
借助有限元分析软件Abaqus/Explicit建立了中型H型钢连轧过程的有限元模型,通过截面控制技术实现了连轧过程的有限元模拟,着重分析了型钢热连轧过程中轧件金属的流动情况和变形规律。分析表明,由于变形条件不同,H型钢万能轧制腹板与翼缘变形不太一致,并且腹板与翼缘连接处金属变形最为复杂,轧边机轧制时主要对翼缘端部压下,制定规程时应以万能轧制时为主。研究为H型钢的轧制工艺、改进产品质量、合理制定万能压下规程提供了依据和参考。
|
|
With the aid of FEM software Abaqus/Explicit, the FEM model of hot continuous H-beam rolling process was built and the simulation was finished through section control technique. Based on simulation result, the flow and deformation of blank metal in the stable rolling phase were discussed. The analysis shows that metal will flow inward along the surface of H-Beam groove, deformations in web and flange is different, and deformation in conjunction of web and flange is the most complex; the edge mills mainly work on the flange edge, therefore, the universal mills should be taken as the first priority when rolling plans are made.The references were given to the rolling mill practice.
|
|
基金项目：
|
|
山东省科技创新基金资助项目(2003182);;
高等学校博士点学科专项基金资助项目(20050422032)
|
|
作者简介：
|
|
|
|
参考文献：
|
[1]朱旭光,程鼎.H型钢万能轧制宽展分析[J].轧钢,2006,23(1):22-26.
[2]程眉,张治民,于建民.多向塑性成形数值模拟研究[J].锻压技术,2007,32(5):129-132.
[3]贺庆强,张勤河,刘克强,等.型钢热轧全过程有限元仿真[J].武汉理工大学学报,2006,28(10):118-122.
[4]贺庆强,张勤河,刘克强,等.型钢热轧开坯过程金属变形分析[J].塑性工程学报,2007,14(4):115-119.
[5]曹杰,奚铁,章静,等.H型钢万能轧制变形分析[J].重型机械,2005,(1):23-25.
[6]陈伟,朱国明,康永林,等.H型钢X-H三机架往复连轧过程三维有限元分析[J].塑性工程学报,2007,14(4):110-114.
[7]崔振山,刘才,卜勇力.H型钢热轧过程金属流动的数值模拟[J].塑性工程学报,1999,6(3):74-78.
[8]汪家才.金属压力加工的现代力学原理[M].北京:冶金工业出版社,1991.
|
|
服务与反馈：
|
|
【本网站尚未开通全文下载服务】【加入收藏】
|
|
|
|
