锻压技术

工艺参数对薄壁筒变薄旋压的表面残余应力的影响

英文标题：Influence of process parameters on surface residual stress for thin-wall cylindrical part in the reduction spinning

作者：张坦李新和骆亚洲常士武魏准

单位：中南大学

关键词：薄壁筒形件旋压残余应力三维弹塑性有限元模拟 Hastelloy C276

分类号：TG301

出版年,卷(期):页码：2017,42(1):47-53

摘要：

针对Hastelloy C276大径厚比薄壁筒形件，建立三维弹塑性有限元模型，通过不同工艺参数（毛坯壁厚、减薄率、进给比）对其表面残余应力的影响进行分析，研究了筒形件变薄旋压残余应力的分布规律，提出了合理的旋压工艺参数范围，并通过旋压实验对仿真模型进行了实验验证。研究表明：壁厚越薄，残余应力的绝对值越大，变化幅度也越大；表面残余应力的绝对值随减薄率的增加而增加；随着进给比的增大，各向残余应力的变化情况都不相同，周向和轴向残余应力的绝对值随进给比的增加而增加，而径向残余应力相反。

For Hastelloy C276 thin-walled cylindrical part with large diameter-thickness ratio, a 3D elastic-plastic finite element model was established, and the influences of different process parameters (wall thickness of blank, reduction ratio and feed rate) on surface residual stress were analyzed. Then, the distribution regularity of residual stress for cylindrical part reduction spinning was studied, the reasonable spinning process parameter range was put forward, and the simulation model was verified by spinning experiment. The results show that the thinner the wall thickness is, the greater the absolute value and rangeability of residual stress are. The absolute value of surface residual stress increases with the increase of reduction ratio. While with the increase of feed rate, changes of all the residual stresses are not the same, and the absolute values of circumferential and axial residual stresses increase with the increase of feed rate, but the radial stress is on the contrary.

基金项目：

国家重点基础研究发展计划（“973”计划）（2015CB057305）

张坦（1990-），男，硕士研究生 E-mail：979267157@qq.com 通讯作者：李新和（1957-），男，博士，教授 E-mail：1378239904@qq.com

参考文献：

[1]赵云豪，李彦利.旋压技术与应用[M]. 北京:机械工业出版社, 2007.

Zhao Y H, Li Y L. The Technology and Application of Spinning[M]. Beijing: China Machine Press, 2007.

[2]舒成龙，樊文欣，原霞，等. 基于响应曲面法的衬套强力旋压工艺参数优化设计[J]. 锻压技术，2015，40（4）：60-63.

Shu C L，Fan W X，Yuan X，et al. Parameters optimal design of power spinning process for bushing based on response surface method[J]. Forging & Stamping Technology，2015，40（4）：60-63.

[3]吕炎，刘英伟，单德彬. 筒形件强旋三维刚塑性有限元分析[J].中国有色金属学报，1999，9（1）：118-122.

Lyu Y, Liu Y W, Shan D B. 3D rigid-plastic FEM analysis of cylindrical workpiece power spinning[J]. The Chinese Journal of Nonferrous Metals, 1999，9（1）：118-122.

[4]Mohebbi M S, Akbarzadeh A. Experimental study and FEM analysis of redundant strains in flow forming of tubes[J]. Journal of Materials Processing Technology, 2010, 210(2): 389-395.

[5]葛文翰. 旋压筒形件的残余应力的分析研究[J]. 锻压装备与制造技术, 1985, 20(3): 2-7, 12.

Ge W H. Analysis of the residual stresses for the spinning cylindrical parts [J]. China Metalforming Equipment & Manufacturing Technology, 1985, 20(3): 2-7, 12.

[6]Joseph Davidson M, Balasubramanian K, Tagore G R N. Experimental investigation on flow-forming of AA6061 alloy-A Taguchi approach[J]. Journal of Materials Processing Technology, 2008, 200(1-3): 283-287.

[7]Joseph Davidson M, Balasubramanian K, Tagore G R N. Surface roughness prediction of flow-formed AA6061 alloy by design of experiments[J]. Journal of Materials Processing Technology, 2008,202(1-3):41-46.

[8]高桥金. 基于有限元分析和试验对旋压残余应变的研究[J]. 热加工工艺, 2013, 42(17):83-85.

Gao Q J. Study on redundant strains in spinning based on FE analysis and experiment[J]. Hot Working Technology, 2013, 42(17):83-85.

[9]孙桂香, 华寿美. 冷旋压变形与残余应力探讨[A]. 全国第六届材料科学与工程、合金加工学术会议[C].北京, 1997.

Sun G X, Hua S M. Cold spinning deformation and residual stress[A]. The Sixth National Academic Conference on Materials Science and Engineering, Metal Processing[C].Beijing,1997.

[10]张涛. 旋压成型工艺[M]. 北京：化学工业出版社，2009.

Zhang T. The Forming Technology of Spinning[M]. Beijing: Chemical Industry Press, 2009.

[11]张美君，刘福贺. 铝合金多楔带轮旋压成形数值分析与试验研究[J]. 锻压技术，2015，40（2）：79-86.

Zhang M J，Liu F H. Numerical analysis and experimental study on spinning forming of Al alloy multiple V-groove pulley [J]. Forging & Stamping Technology，2015，40（2）：79-86.

[12]佘勇, 樊文欣, 陈东宝, 等. 基于RBF神经网络的强力旋压连杆衬套力学性能预测研究[J]. 锻压技术, 2016, 41（6）:128-132，145.

She Y，Fan W X，Chen D B，et al. Study on mechanical property prediction of power spinning connecting rod bushing based on RBF neural network[J]. Forging & Stamping Technology，2016, 41（6）:128-132，145.

[13]高立，樊文欣，马学军，等. 基于RBF神经网络的强力旋压连杆衬套成形质量预测研究[J]. 锻压技术，2015，40（9）：134-138.

Gao L，Fan W X，Ma X J，et al. Study on forming quality prediction of connecting rod bushing by power spinning forming based on RBF neural network [J]. Forging & Stamping Technology，2015，40（9）：134-138.

服务与反馈：

【本网站尚未开通全文下载服务】【加入收藏】