网站首页期刊简介编委会过刊目录投稿指南广告合作征订与发行联系我们English
热轧铝板带横向非对称平衡调控建模及数值模拟
英文标题:Balance regulation model and numerical simulation on lateral non-symmetrical phenomenon in hot rolled Al alloys
作者:马立勇 刘义伦 付卓 
单位:河北建筑工程学院 中南大学 
关键词:热轧铝板带 横向非对称 平衡调控 数值模拟 
分类号:TG339
出版年,卷(期):页码:2014,39(11):130-134
摘要:
针对铝板带热连轧过程中出现的来料厚差、来料初始偏心和初始设定辊缝差等横向非对称诱因的特点,分别建立了平衡调控模型。利用MSC.Marc软件进行了JP1235铝合金热轧有限元分析,将实验所得JP1235铝合金材料本构关系及某铝板带五连轧生产设备生产数据应用于调控模型中,对横向非对称诱因扰动下轧件的跑偏情况和施加平衡调控后的轧件跑偏情况进行了数值模拟。模拟结果显示,平衡调控数学模型能够有效地减小横向非对称扰动造成的轧件横向跑偏:初始偏心的调控模型在系统响应1.2 s左右跑偏量基本为0,初始厚度横向楔形和初始辊缝差的平衡调控对轧件的跑偏缓解程度都在60%以上。模拟结果证明平衡调控模型有效,达到了理想纠偏效果。
 
For the lateral non-symmetrical characteristics caused by original thickness difference, initial eccentricity and initial set roll gap difference i.e. in hot rolled Al alloys process, balance regulation models were founded. The hot rolling process of JP1235 Al alloys was analyzed by MSC.Marc software. Deviation situation before and after balance straightening was simulated based on the regulation model that formed by both the constitutive relation of JP1235 Al alloy obtained experimentally and practical data coming from a five-stand Al rolling equipment. The results show that balance regulation models can effectively reduce the lateral deviation of parts caused by lateral non-symmetry. The deviation caused by initial eccentricity decreases to near 0 after the system response 1.2 s. The deviations caused by initial thickness wedge and initial roll gap are released by over 60%. Therefore, it is proved that the balance regulation model is highly effective, and the result is desirable. 
 
基金项目:
国家自然科学基金资助项目(51375500);湖南省教育厅资助项目(2013SK2001);湖南省科技计划资助项目(2012GK3171);中南大学中央高校基本科研业务费专项资金资助项目(2013zzts037)
作者简介:
马立勇(1987-),男,硕士研究生
参考文献:


[1]甄玉波, 肖广耀, 张成瑞, 等. 唐钢超薄热带生产过程中的跑偏现象分析与纠偏措施[J]. 冶金标准化与质量, 2007,45(1):24-27.Zhen Y B, Xiao G Y, Zhang C R, et al. The analysis of ultra-thin strip running off in Tangshan Steel and some correcting measures [J]. Metallurgical Standardization & Quality, 2007, 45(1): 24-27.
[2]李振兴, 胡贤磊, 刘相华. 中厚板侧弯与楔形的关系分析[J]. 轧钢, 2010,(4):10-12.Li Z X, Hu X L, Liu X H. Analysis of relationship between camber and wedge of plate [J]. Steel Rolling, 2010,(4):10-12.
[3]赵宪明, 刘相华, 王国栋, 等. 板坯轧制过程中不对称工艺参数对侧弯的影响[J]. 钢铁, 2003,(3):25-28.Zhao X M, Liu X H, Wang G D, et al. Influence of asymmetrical technical conditions during roughing on bar camber [J]. Iron and Steel, 2003, (3):25-28.
[4]何纯玉, 吴迪, 赵宪明. 中厚板轧制过程横向厚度的计算方法[J]. 东北大学学报:自然科学版, 2009, 30(12):1751-1754.He C Y, Wu D, Zhao X M. Calculation of transversal slab thickness during plate rolling [J]. Journal of Northeastern University: Natural Science, 2009, 30(12):1751-1754.
[5]Yildiz S K, Forbes J F, Huang B, et al. Dynamic modelling and simulation of a hot strip finishing mill [J]. Applied Mathematical Modelling, 2009,33(7):3208-3225.
[6]Hwang Y, Tzou G. An analytical approach to asymmetrical hot-sheet rolling considering the effects of the shear stress and internal moment at the roll gap [J]. Journal of Materials Processing Technology, 1995,52(2):399-424.
[7]Karhausen K F, Roters F. Development and application of constitutive equations for the multiple-stand hot rolling of Al alloys [J]. Journal of Materials Processing Technology, 2002, 123(1):155-166.
[8]Takahashi R. State of the art in hot rolling process control [J]. Control Engineering Practice, 2001,20(9):987-993.
[9]王培起, 张勤河, 马汝颇, 等. 基于 ABAQUS 的大型 H 型钢热轧仿真系统开发[J]. 锻压技术, 2012,37(6):146-151.Wang P Q, Zhang Q H, Ma R P, et al. Development of simulation system for large H-beam hot rolling based on ABAQUS[J]. Forging & Stamping Technology, 2012, 37(6): 146-151.
[10]Nilsson A. FE simulations of camber in hot strip rolling [J]. Journal of Materials Processing Technology, 1998, 80: 325-329.
[11] Li X, Wang M, Du F. A coupling thermal mechanical and microstructural FE model for hot strip continuous rolling process and verification [J]. Materials Science and Engineering: A, 2005, 408(1):33-41.
[12]康煜华, 刘义伦, 何玉辉. 铝合金轧制过程中的热力耦合分析[J]. 锻压技术, 2008,33(5):92-94.Kang Y H, Liu Y L, He Y H. Thermo-mechanical coupled simulation during rolling on aluminum alloys[J]. Forging & Stamping Technology,2008,33(5):92-94.
[13]刘义伦, 周红平, 赵先琼. 楔形板带轧制过程跑偏计算模型及其仿真[J]. 工程设计学报, 2008,15(6):444-447.Liu Y L, Zhou H P, Zhao X Q. Camber calculating model and simulation of wedge strip in rolling [J]. Journal of Engineering Design, 2008,15(6):444-447.
[14]凌于蓝, 刘义伦, 周维, 等. 热轧铝板带跑偏模糊控制研究[J]. 锻压技术, 2014,39(3):137-140.Ling Y L, Liu Y L, Zhou W, et al. Deviation contral research for hot rolled aluminum plate based on fussy theoy[J]. Forging & Stamping Technology, 2014,39(3):137-140.

服务与反馈:
文章下载】【加入收藏
《锻压技术》编辑部版权所有

中国机械工业联合会主管  中国机械总院集团北京机电研究所有限公司 中国机械工程学会主办
联系地址:北京市海淀区学清路18号 邮编:100083
电话:+86-010-82415085 传真:+86-010-62920652
E-mail: fst@263.net(稿件) dyjsjournal@163.com(广告)
京ICP备07007000号-9